>> 模型介绍 | Model Introduction >>>>>>>>
虽然不喜欢多色打印，但CFS毕竟也是供料，能做续料盒子，还是咬咬牙买了！不得不说选择创想三维是对的，最终还是给老用户带来了惊喜，给K1系列做了多色升级，这点一定、必须加以点赞！入手前反反复复看了好多次安装视频，总觉得有个点格格不入，没有错！就是这个点让我无法接受——都是改装件到最后竟然给缓冲器贴了个背胶就贴上去，而且如此贴法不是将CFS盒子的最优摆放位置限定在打印机左边了吗，最重要的是我打印机左边刚好没有空位，这个必须差评，希望创想三维能好好反省！
趁着刚买的CFS盒子和K1系列多色升级包没有上机改装前，立马动手打造，利用原先单卷支架留下的口造了个缓冲器支架。虽然本来想着做个活动件的，但是，发现缓冲器上原本就留着螺丝孔（明显创想三维这是在省料，差评再+1！），冲着这两个螺丝口做了个简单的面板拧上螺丝固定完工，进线口向下不就没有了位置放置的限制了吗，当然还能可以根据自己的CFS摆放位置对支架位置进行靠左靠右调整哈，简单小物件，不喜勿喷，要怪就怪创想三维哈🤣。
Although I'm not a fan of multi-color printing, the CFS feeder is still a feeding solution that supports continuous filament supply. So, I gritted my teeth and bought it! I have to say, choosing Creality was definitely the right decision—it's truly impressive how they continue to surprise long-time users by offering a multi-color upgrade for the K1 series. This deserves a big thumbs-up!
Before purchasing, I watched the installation video countless times, and something kept bothering me. And yes—I was right not to feel right about it! My issue is this: using double-sided tape to attach the buffer feels unacceptable. Not only does this method limit the optimal placement of the CFS box strictly to the left side of the printer, but in my case, there’s absolutely no space on the left side of my printer at all. For this reason, I must leave a negative comment and sincerely hope Creality will reflect on this design choice.
Since I hadn't yet installed the newly purchased CFS box or the multi-color upgrade kit onto my K1 series printer, I immediately got to work modifying things. Using the existing mounting holes from my previous single-spool holder, I created a dedicated bracket for the buffer. Originally, I intended to make an adjustable (movable) mount, but then I noticed the buffer already had pre-drilled screw holes—clearly indicating this part was designed to be screwed in (another cost-cutting move by Creality, another negative point ⚠️). Based on those screw holes, I made a simple mounting plate, secured it with screws, and finished the installation. By orienting the cable entry downward, the positional limitations were completely eliminated. Plus, you can now adjust the bracket left or right based on where you place your CFS box.
It's just a small DIY modification—no need to take it too seriously. If anyone's upset about it, blame Creality! 😄🤣
| 类别 Category | X | Y | Z |
|---|---|---|---|
| 支架 Bracket | 73.5mm | 73.5mm | 14.6mm |
| 螺丝套 Screw Set | 6mm | 6mm | 23mm |
>> 打印配置 | Print Settings >>>>>>>>
（仅参考，可自定义）
(Referential, Customizable as Needed)
耗材 Filament：PETG
填充 Infill：15%
填充图案 Infill Pattern：网格 Grid
支撑 Support：需要 Required
Brim/Raft: NONE
>> 组装说明 | Assembly Instructions >>>>>>>>
即打即用，简单组装。
Ready to use upon installation; simple assembly required.
缓冲器原本留有螺丝口，但是柱体为6mm，螺丝孔又是3mm的，想象不出来是什么螺丝。所以为了更好适配M3螺丝，给它加了螺丝套。由于我只有M3*30mm的螺丝，所以螺丝套高度为23mm的，请根据自己的螺丝进行调整。
The buffer originally has screw holes, but the post is 6mm in diameter, and the screw hole itself is 3mm — it's hard to imagine what kind of screw was intended for that. So, to better accommodate M3 screws, I added screw inserts. Since I only had M3×30mm screws available, the height of the screw insert is set to 23mm — please adjust according to the screws you are using.
还有，强迫症玩家请在升级前打印哈。🤣
Also, OCD players please print this out before upgrading. 🤣
缓冲器的空位处得给收缩动态（详情看这https://wiki.creality.com/zh/printers-general-documents/FR2851），不然CFS不能进退料，还会闪红灯报错！
将缓冲器连接到双通口的铁氟龙管做个弯曲让其有个伸缩空间，不要直直对着双通口。
The buffer compartment must maintain dynamic clearance for compression cycles (https://wiki.creality.com/zh/printers-general-documents/FR2851). Otherwise, the CFS will fail to feed/retract filament and trigger red error alerts!
Connect the Teflon tube from the buffer to the dual port with a bend, so that it has some space for expansion and contraction — do not point it straight at the dual port.
>> 其他说明 | Additional Notes >>>>>>>>
1. 模型使用 Blender 4.4.3制作。
The model was created using Blender 4.4.3.
2. 可根据协议 CC BY-NC-SA 4.0 自行修改为所需样式使用。
You are free to modify it as needed to suit your desired style under the terms of the CC BY-NC-SA 4.0 license.
3. 无论如何，遇见是缘分，能用是巧合，欢迎点赞加收藏，感谢关注和助力！
Regardless of fate bringing us here, it's a happy accident that I could help—click like and save this post! Many thanks for your following and the boost!
4.本篇英文翻译出自于DeepSeek。
This English translation is powered by DeepSeek.
>> 模型下载 | Model Download >>>>>>>>
CrealityCloud（创想云）
MakerWorld（拓竹）
MakerOnline（纵维立方）
>> 实物购买 | Physical Purchase >>>>>>>>
